【USA】 4 Axis Nema 23 Stepper Motor Driver Mach3 USB Control Board 24V DC CNC Kit

Description: 【USA】 4 Axis Nema 23 Stepper Motor Driver Mach3 USB Control Board 24V DC CNC Kit for CNC Router Engraving Milling Machine Good News: We have USA Warehouse in USA,so we will ship this product from USA to you Parcel include:4× 23HS8430 Nema23 stepper motor 76mm 270oz-in 3A 1.8°4× TB6600 stepper motor driver1× 4 Axis USB Mach3 control board1× USB Cable1× 350W 24V DC switching power supply1× CD disc include user manual and mach3 software Product Description4 Axis Nema23 Stepper Motor Driver USB Mach3 Board Power Supply CNC Controller Kit 23HS8430 Nema23 stepper motorPhysical SpecificationFrame Size: 57 x 57 x 76 mmBody Length: 76mmNumber of Leads: 4Weight: 1.1kgSingle shaft is 8mm diameter,21mm lengthMain specifications* Motor Type: Hybrid* Step Angle: 1.8 degree* Holding Torque: 1.8Nm (270oz.in) 18kg.cm* Phase Resistance: 1ohms* Rated Current/phase: 3A* Inductance:3.5mH+/-20%(1KHz)* Frame Size: 57x57x76 mm* Phase: 2 phase* Insulation class: B4-Lead WiresStepper motor's red wire connect to driver's A+ portStepper motor's green wire connect to driver's A- portStepper motor's yellow wire connect to driver's B+ portStepper motor's blue wire connect to driver's B- portTB6600 stepper motor driverSuitable for Nema17 Nema23 two-phase/four-phase/four-wire/six-wire stepper motors which currently within 4.2A.The level of the input pulse is 5V, if it is a 12V level pulse, a 1K resistor is required, if it is a 24V level pulse, a 2.4K resistor is required.The motor runs when the CLK has pulses, and automatically enters the set half-current state when there is no pulse, and the motor is locked.The motor rotates forward when CW is high or suspended, and reverses when it is low.When EN is onhigh or floating, it is working state, when it is on low, it is offline.FeaturesIt adopts the common anode input mode, there are two input terminals, the wiring is more convenient;The working voltage is DC 10V-45V. recommended DC 24V;Adopt 6N137 high-speed optical lotus root to ensure high speed without losing step.Using Toshiba's new high-current, high-voltage TB6600HG brand new original chip, with low-voltage shutdown, overheating shutdown and over-current protection circuits, and short-circuit protection added compared to TB6560.The rated maximum output reaches: ±4.5A.The output current is steplessly adjustable.Subdivision: full step, half step, 1/4 step, 1/8 step, 1/16 step, maximum 16 subdivisions.Automatic half-flow functionAdopt enlarged radiator, good heat dissipationWith output short-circuit protection function.Wirings between driver & mach3 board (for example X-axis):Driver's "CLK-" connects to control card's XP pinDriver's "CW-" connects to control card's XD pinDriver's "5V" connects to control card's 5V pinNote:The power supply cannot be connected reversely, otherwise the chip will be burnt out.The set current should not exceed the rated current of the motor.4 Axis USB Mach3 control boardSupport for 4 Axis linkage, you can connect four stepper motor drives or servo drives;Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor;Have 0-10V signal output,you can use mach3 software to control the spindle motor speed.One status LED, indicate connection status on the board.Need use external 24V DC power supply to isolate USB and external port, and to make the system more stable.Support for connecting electronic handwheel;Handwheel interface: 2 * 5P row needleMCU model: three generation 32-bit STM processorCommunication plug-in: RnR motion control card - ECO-2.04 general-purpose isolated relay drive output interface, can drive four relays for controlling the spindle starts, forward rotating and reverse rotating, pumps and other device.4 general-purpose inputs, you can connect the limit switch, estop switch, probe , back to zero and other device.Wiring diagramsPlease strictly follow the instructions and warnings before using this product:It is recommended that the limit switch and emergency stop switch must be installed first and can be used normally.The output singal of theelectronic handwheel must be 5V, more than 5V output will damage the hand wheel interface.This interface can output 0-10V analog signals, and can also be configured as 0-5V output.USB interface is applicable to any netbook, notebook, desktop, tablet and other PC compatible computers with USB interface.This control board does not require any drivers to be installed,as long as Mach3 can run, the control card can be used;Support computer system: Windows 2000/ XP / Windows 7/8The inverter interface (AVI +, AVI-) is isolated from the computer and the main control circuit, and has strong anti-interference ability,no interference signal will be introduced due to the introduction of external strong electrical equipment.Whether frequency converter is supported: YesSupport PWM: YesNumber of control axes: X.Y.Z.A axis350W 24V DC switching power supplyDC output voltage: 24VOutput current: 0-14.5AInlet stability: ±0.5%Load stability: ±0.5%DC voltage of Adjustable range: ±10%AC input voltage range: 110V-120V AC or 220V-240V AC; 115VAC/6.5A/50HZ or 230VAC/3.4A/60HZ; Selected by side switch.Four fold protection settings, multiple protections, stable performance, effectively reducing the impact of AC input.Dual ball cooling fan and all metal casing designIt has the characteristics of fast speed and good performance, which can ensure the temperature operation of the equipment and extend its service life.The shell is made of aluminum alloy and has a high thermal conductivity system, which is reinforced and durable, and the design is more user-friendly.Short circuit protection: when the output terminal is short circuited, the power is turned off and the output voltage is 0V.Overcurrent protection: when the output current is>115-150%, the output voltage is turned off.Overload protection: power protection when the load power is greater than 105-135% of the rated power.Temperature protection: the power supply is automatically protected under high temperatures.Working Temperature: -10℃～+50℃Setup/rise/hold-up time: 200ms、50ms、20ms/230VAC at full loadWithstand voltage: I/P-O/P: 1.5KvAC; I/P-FG: 1.5KvAC; O/P-FG: 1.5KvAC; 1minuteIsolation resistance: I/P-O/P、 I/P-FG、O/P-FG: 500VDC/100MΩ Shipping Please open the package and check if there are some damages before sign, if there are some damages , please do not sign and contact us immediately Items will be shipped within 1-2 days upon the receipt of payment. Problem&Feedback Please give us the opportunity to resolve any problem when you have, we concern your problem and we will try our best to resolve it. We are a new member in ebay now, and need understand both of sides Pls email us before you want to leave any negative feedback Refund When you have the parcel, and not satisfied the goods or it is other problem like as broken,pls tell us the detail reason and provide the photos Any reason required for all refund. Item must be in it's original condition and no physical damage. Buyer responsible for all shipping cost Contact us Welcome worldwide customer inquire and questions, we will try to do our best to feedback customer’s email within 1-2 business days,if not pls check the mail box again Customer’s satisfaction is very important to us.

Price: 130 USD

Location: New York

End Time: 2024-08-29T06:24:35.000Z

Shipping Cost: 0 USD