Blue Wonder Gun Bluing Kit -Quick easy touchup or re-finish your gun, SHIPS FREE

Description: Blue Wonder™ Gun Blue✔NEW ✔Low Price ✔FREE U.S. Shipping ✔Authorized DealerFactory Blue in a Bottle Blue Wonder Gun Black looks and wears like original factory black. This Kit gives you everything you need to repair that scratch in your favorite gun or the wear from years of hard work or completely and professionally apply a new factory black finish to the entire weapon.Everything you need for touch-ups or complete re-bluing of one to three long guns. The Gun Blue Kit includes a 1 oz. tube of Blue Wonder™ Gun Cleaner, the 2 oz. Blue Wonder™ Gun Blue, a 1/2 oz Developer tube as well as a 1/2 oz tube of XFR Lubricant for corrosion protection. This complete package gives you everything you need to provide the best care for the valuable investment you have in your guns! This will serve you for dozens of bluing touch-up jobs and up to six complete re-bluing projects. No need to put up with that holster wear anymore! Looks and wears like factory blue Easy to apply This Gun Blue Kit contains the following: Blue Wonder™ Gun Blue – 2 Oz. Blue Wonder™ Developer - 0.5 Oz. Blue Wonder™ Gun Cleaner - 1 Oz. Blue Wonder™ XFR Lubricant - 0.5 Oz. Instructions for use of this product can be found here. Important: Blue Wonder™ Gun Blue and Gun Black are completely different than any “Cold Blue” you may have tried before. It does not oxidize the metal but rather, bonds to and colors the metal in a two part process, producing a beautiful, durable finish that rivals any factory or hot blue. For that reason, be sure to follow ALL directions closely to achieve the desired results. Wear rubber gloves to protect hands and keep finger oils and acids off of the metal. DO NOT USE acetone, solvents, cleaners, degreasers, rust removers or any chemicals other than Blue Wonder™ Gun Cleaner to prepare the metal prior to refinishing. These products can leave residues in the pores of the metal and interfere with the bonding process of Blue Wonder™ Gun Blue/Black. 1. If it is necessary to remove old factory blue, cold blue or other finishes, use Blue Wonder™ Blue Removal System which is formulated for complete compatibility and superior results. (Skip this step for touch-ups or for a new gun). DO NOT USE Birchwood Casey® or any other blue removers as they can leave residues which interfere with the bonding process. Factory finishes can also be removed by using ScothBrite® abrasive pads in combination with Blue Wonder™ Gun Cleaner. Remove any rust using Blue Wonder™ Gun Cleaner following instructions for rust removal. 2. For best results, the areas to be refinished should be free from pits, scratches, etc. These can be removed using ScothBrite® abrasive pads and/or emery cloth. For a higher gloss finish, polishing compound or jeweler’s rouge may be used; however, prior to refinishing, you must soak the piece overnight in lacquer thinner to remove all residues and then proceed to step #3 below. If the surface is cleaned and prepared properly, Blue Wonder™ Gun Blue/Black will apply evenly and without streaking, even on polished surfaces. 3. After surface is properly prepared, clean all areas thoroughly using Blue Wonder™ Gun Cleaner with “0000” steel wool to remove any oil, lacquer thinner, grease, fingerprints, etc. 4. Apply a coat of Blue Wonder™ Gun Cleaner gel to areas to be refinished and “while the gel is on the metal” use a propane torch, heat gun or hair dryer and heat the area to 120°F - 140°F (hot to the touch but not hot enough to cause a burn). Using a paper towel, completely wipe the hot gel off of the metal. Do not touch the piece with bare fingers or let it contact any oil, grease or other substance as the bluing will not bond to these areas. 5. SHAKE the Blue Wonder™ Gun Blue/ Black vigorously before use and “While the metal is still hot” apply with a soft paper towel. Wad up the paper towel and “Saturate” an area of it with the Gun Blue. Wipe it liberally on the areas to be refinished until well wetted, using gentle even strokes. Re-wet the paper towel with Gun Blue as needed and shake the bottle before each application. Continue using the same area of the towel, otherwise it will absorb too much liquid. Apply as many coats as needed to obtain the desired darkness (minimum 5-6; maximum 15-16). Blue Wonder™ Gun Blue/Black will not remove, harm, bond to or affect factory finishes, so for “TOUCH-UPS”, apply it to the bare areas and overlap the factory finish until it blends in and matches. 6. Promptly apply Blue Wonder™ Developer to the newly blued areas using a paper towel and wipe off any excess. The developer dries and sets the Gun Blue and brings out a deep, dark luster. Let the piece set for 1-3 hours and then apply Blue Wonder™ Disotec XFR Premium Lubricant or other gun oils with good corrosion protection properties such as Break-Free™ CLP. DO NOT USE “3 in 1” oil, motor oil, WD-40®, Rem-Oil®, Hoppes® or Outers® gun oils for this step. The process is now complete and you may and handle the piece as you would any factory new gun. The new finish will become even more durable over the next 3-4 weeks as it “cures”. Note: In areas with high humidity, rusting may occur soon after the refinishing process. In these areas apply Disotec XFR after one (1) hour. 7. If the desired darkness has not been obtained, clean the areas with Blue Wonder™ Gun Cleaner, re-heat following step 4, and then apply additional coats of Blue Wonder™ Gun Blue/Black following steps 5 and 6. *Your mileage may vary.NOTES: Only works on carbon steel, does not work on stainless steel nor aluminum. Not returnable if any of the bottles are opened!

Price: 37.98 USD

Location: Maryville, Illinois

End Time: 2025-01-16T20:16:58.000Z

Shipping Cost: 0 USD