Description: 1.8µ & 2.5µ Aluminum Foil (one of each)99.1% Aluminum Foil sheets for damaged ribbons and upgrades. One sheet is 1.8µ thick and the other is 2.5µ thick. See below for individual sheet specs.Why upgrade the ribbon to a 1.8µ ribbon? Most (not all) of the Chinese Ribbon microphones use 6µ aluminum foil which isn't as responsive as 1.8µ. Basically by lowering the mass of the ribbon you will increase the output voltage and frequency response slightly (a marginal increase, not much at all). Specifications For 1.8 micron Aluminum Foil SheetThickness: 1.8µ (.00018 cm, .0018 mm, .000072 inches)Width: 7 cm (70 mm, 2.755910 inches) ***Length: 10.5 cm (105 mm, 4.133858 inches) ***Area (squared): 73.5 cm^2 (7350 mm^2, 11.392540 inches^2)Material: 99.1% Aluminum Specifications For 2.5 micron Aluminum Foil SheetThickness: 2.5µ (.00025 cm, .0025 mm, .000098 inches)Width: 6.25 cm (62.5 mm, 2.46063 inches) ***Length: 12.5 cm (125 mm, 4.92126 inches) ***Area (squared): 78.125 cm^2 (7812.5 mm^2, 12.10939 inches^2)Material: 99.1% Aluminum ***Tolerances: +/- 2 mm HANDLE WITH CARE. We are not responsible for the foil once you start handling it. The smallest burst of air can flip the foil over, bend it, or tear it. If you fold the material on accident you can smooth it out easily by putting it back in the tracing paper and running your fingers over the tracing paper until it is flat again TipsUse a cutting mat not a cutting board. You can find on amazon or a local hobby store.Make sure to clean the mat of debris to keep your cut nice and straight.Use a very sharp cutting tool (exacto).Cut slow and steady. Avoid starting and stopping.We like to keep the foil between the two sheets of tracing paper when cutting it to the desired width. This will help to avoid tear out on the edges. Buy some extra tracing paper to store the foil because every time you make a cut you will also cut the tracing paper and eventually run out of the supplied tracing paper.Use a flat ruler as a guide and apply enough pressure so the material doesn't move on you. Cut the ribbon to an over sized length. We like to cut a piece the entire length (longest dimension) of the raw material to make sure we can handle and install the ribbon properly.Have patience. It takes some practice. Try practicing on regular foil first to see how the material responds to cutting. You can also buy some 0.3µ-0.6µ imitation silver leaf to practice on. If you can cut this you will have NO PROBLEM cutting a thicker foil. Packaging We package the material between two pieces of acid free tracing paper. The material and tracing paper is then sandwiched between two pieces of thick poster board. Finally we ship the sheet in a non bendable mailer. Returns Returns are NOT accepted, BUT we will replace the material if it is damaged in transit. A few nicks in the material edges will not be considered damaged. This is normal for this thin of a material.International Buyers – Please Note: Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyer's responsibility. Please check with your country's customs office to determine what these additional costs will be prior to bidding or buying.
Price: 35 USD
Location: Arlington, Texas
End Time: 2024-10-15T22:22:38.000Z
Shipping Cost: 0 USD
Product Images
Item Specifics
Restocking Fee: No
Return shipping will be paid by: Buyer
All returns accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money Back
Brand: Geistnote
Form Factor: DIY RIBBON MOD KIT
MPN: Does Not Apply
Type: Ribbon Microphone